Sample Review Questions:
1. A/C compressors in most late model vehicles require what type of lubricant?
a. PAG oil
b. POE oil
c. Mineral oil
d. Motor oil
2. All of the following statements about A/C condensers are true EXCEPT:
a. It is usually located in front of the radiator
b. It receives high-pressure refrigerant gas from the compressor
c. It cools the air entering the passenger compartment
d. It cools the refrigerant so the gas will condense into a liquid
3. The orifice tube in an A/C system is located where?
a. In the suction hose
b. Between the evaporator and compressor inlet
c. Between the compressor and condenser
d. Between the condenser and evaporator
4.
Counterman A says the accumulator should always be replaced if an A/C
system has been opened up for repairs. Counterman B says a plugged
orifice tube is a common cause of compressor failure. Who is right?
a. Counterman A only
b. Counterman B only
c. Both Counterman A and B
d. Neither one
ANSWER KEY
1A, 2C, 3D, 4C
EXPLANATIONS:
1.
Mineral oil is used to lubricate compressors on older R-12 applications
(pre-1994 vehicles). If an older R-12 A/C systems has been converted
(retrofitted) to R-134a refrigerant, POE (polyester) oil can be used,
or the type of PAG specified by the compressor manufacturer. The reason
why mineral oil should not be used with R-134a is because it does not
mix with the refrigerant. This prevents the oil from circulating
through the system normally, which may cause the compressor to fail.
Almost all late model (1995 and up) vehicles with R-134a A/C systems
specify PAG oil. Using the wrong viscosity of PAG oil may also a
compressor to fail.
2. The condenser is a large heat exchanger
located in front of the radiator. It receives hot compressed
refrigerant gas from the compressor. Air flowing through the cooling
fins in the condenser absorbs heat and cools the refrigerant, allowing
the refrigerant to condense into a liquid. This is necessary so the
refrigerant can provide a cooling effect when it flows to the
evaporator and is allowed to revaporize. A dirty condenser will reduce
the cooling efficiency of the A/C system. A larger or more efficient
condenser can improve cooling, and may be recommended if the original
condenser is being replaced or is not cooling well in an older vehicle
that has been converted to R-134a. If the A/C system is contaminated
internally with sludge or debris from a compressor failure, the
condenser should be cleaned or replaced.
3. The orifice tube
is located in the high-pressure liquid line between the compressor and
evaporator (usually at the evaporator inlet). The orifice tube has a
small opening that meters how much refrigerant enters the evaporator.
This restriction separates the high- and low-pressure sides of the A/C
system, and allows the refrigerant to expand and cool inside the
evaporator. If the orifice tube becomes clogged, it will block the flow
of refrigerant and cause a loss of cooling. The orifice tube should
always be replaced following a compressor failure.
4. The
accumulator (also called a Receiver Drier) is a small metal canister
that stores excess refrigerant and also contains a bag of “desiccant”
crystals to absorb moisture. This prevents the formation of harmful
acids and sludge that could damage the A/C system. The accumulator
should be replaced when changing a compressor, or if the A/C system has
been open and exposed to air for a long period of time. If the small
opening in the orifice tube becomes plugged with sludge, it can block
the flow of refrigerant and compressor oil through the system.
Sections covered:
Automatic Transmission
Batteries
Brakes
Cooling System
Drivetrain
Emissions
Engine Mechanical Parts
Exhaust
Fuel System
HVAC
Gaskets
Ignition System
Manual Transmission
Suspension and Steering
Management