Counterman
Search
Article > Parts & More

How Can You Tell if a Head Gasket is Leaking or Has Failed?


3/9/2010
By Larry Carley

The first symptoms of a head gasket that is failing are usually a slow loss of coolant with no visible leaks, engine overheating and/or a Check Engine light with cylinder misfire codes.
 
The first symptoms of a head gasket that is failing are usually a slow loss of coolant with no visible leaks, engine overheating and/or a Check Engine light with cylinder misfire codes.

The first symptoms of a head gasket that is failing are usually a slow loss of coolant with no visible leaks, engine overheating and/or a Check Engine light with cylinder misfire codes.

The Onboard Diagnostic II system should detect any misfires that occur due to a loss of compression or spark plugs fouled by coolant seeping into a combustion chamber. So if a vehicle has a Check Engine light on and a cylinder misfire code, the spark plug in that cylinder should be removed and inspected for coolant fouling. A compression or leak-down test should also be done to see if the cylinder is losing compression. Internal coolant leaks caused by a leaky head gasket can usually be diagnosed by pressure-testing the cooling system.

Regardless of the cause, a head gasket failure is bad news for the vehicle owner.

Depending on the application and how much labor it requires, the repair bill might run $1,500 or more for parts and labor. The parts required to replace a head gasket include not only the head gasket itself, but also all the other gaskets that have to be replaced to disassemble the top of the engine.

This includes the intake and exhaust manifold gaskets, too, plus new cylinder head bolts if the application is a late model engine with non-reusable torque-to-yield (TTY) head bolts. It may be tempting to save a few bucks on off-brand gaskets.
While these off-brand gaskets might look similar to branded products, they often do not feature the material characteristics and design enhancements required for trouble-free sealing.

Depending on the mileage on the engine, additional parts should also be replaced at the same time. This might include the timing belt if the engine has an overhead cam (recommended replacement intervals for the belt range from 60,000 to 100,000 miles on most vehicles), the water pump, spark plugs and filters. The coolant should also be changed if it is more than five years old, or has more than 150,000 miles on it (long-life coolants), or if it is more than three years old (older green formula coolant). If the head gasket caused an internal coolant leak, it’s possible the oxygen sensor(s) may have also been fouled by silicates in the antifreeze (if the cooling system was filled with older green formula coolant, or a hybrid HOAT or G-05 formula coolant).

What are the risks of reusing torque-to-yield (TTY) head bolts on late-model engines?
The risks are bolt breakage and uneven gasket loading or loss of torque that can cause a newly installed head gasket to leak. TTY head bolts are designed for one-time use because they stretch permanently once they are torqued down. This helps even out the clamping force of the cylinder head on the head gasket.

But if the bolts are reused, stretching them even further greatly increases the risk of the bolt breaking. Some replacement head gaskets come with new TTY head bolts, but others do not. If the bolts are not included, they should be included as an add-on sale. Many customers may not realize they should not reuse TTY head bolts. If an engine has conventional head bolts, it’s okay to reuse them — provided the bolts are in good condition and the bolts are not stretched.

Bolts can be cleaned, then lightly oiled and reused. Dirty or damaged threads, or failing to lubricate the bolts before they are installed can cause false torque readings when the bolts are tightened, which may allow the head gasket to leak.
  Previous Comments
avatar   will   star   4/10/2010   1:33 PM

The best way to tell is to ask your parts pro or mechanic.Regardless off which style you have I always change them.$30 extra now may save you much head ache and trouble down the road.Even on conventional bolts.I'd also recomend going with the new mls gaskets if they are availible to you.they last longer and seal better in my opinion.Just remember that you are repairing one of the most high temp, high pressure ,and most crucial parts of your engine.It's not usually too easy to get too so it takes time and money to repair.Plus if it fails it can cause more problems than just a leaking gasket.Do the job right the first time and replace as much as you need and can afford and then you wont be worrying about it later.



avatar   Jessie   star   4/8/2010   4:27 PM

wut is a simple way for a DIY customer to identify whether he/she has TTY or conventional bolts?



avatar   Gabe   star   3/20/2010   2:52 PM

It should also say if you have a 3.4L GM motor you already do have a blown head gasket! LOL



avatar   Ed   star   3/16/2010   3:23 PM

It is also good practice to have EVERY head checked for warping and aluminum heads resurfaced with every head gasket job.















Advertise     Contact Us     Subscribe    
Babcox Media • www.babcox.com
3550 Embassy Parkway, Akron, OH 44333
330-670-1234 • (FAX) 330-670-0874
Babcox Website Counterman: Home