Belt, hose sales are some of the most lucrative add-on sales opportunities for automotive aftermarket parts professionals

Belt, hose sales are some of the most lucrative add-on sales opportunities for automotive aftermarket parts professionals

Many vehicle owners and technicians forget that heat, load, pressure and atmospheric pollutants eventually deteriorate a vehicle’s rubber parts.

After I earned my driver’s license in 1957, I bought a 1953 Ford V8 so I could drive to school and to work. The striking thing about the 1953 Ford was that, at 40,000 miles, the original-equipment belts and radiator hoses had cracked so badly that I didn’t know if I would make the 70-mile drive home from the dealer’s car lot. In those days, it was suggested that belts and hoses be changed every two years or 24,000 miles. So to avoid dealing with an imminent breakdown, my dad had our local mechanic replace the cracked belts and hoses. I was forever thankful because, at that time, I had neither the tools nor skills to accomplish such a task.

Today, belts and hoses are a routine inspection item and may not need replacement even at 100,000 miles or more of service. Unfortunately, many vehicle owners and technicians forget that heat, load, pressure and atmospheric pollutants eventually deteriorate a vehicle’s rubber parts. City driving is perhaps the hardest on underhood rubber due to the high concentrations of heat and airborne ozone. While over-the-road driving least affects the life of rubber components, a roadside failure can leave a driver stranded for hours in rural areas.

WHY BELTS WEAR
Accessory drive belts transmit engine torque to an assortment of pulley-driven accessories including the water pump, alternator, power steering, air conditioning and air injection pump. In addition to the effects of high underhood temperatures and atmospheric air pollution, frequent use of the air conditioner compressor, power steering pump or alternator tend to accelerate wear on the drive belts.

As the rubber in the belt begins to harden, cracks begin to appear on the belt’s inner circumference. Each crack causes a stress point to develop in the belt’s structural fabric and, as the miles accumulate, the belt becomes more likely to break. Although auto manufacturers consider mild cracking normal, a serpentine or v-belt should be replaced if it exhibits fraying along its edge, deep cracking on its inner circumference or glazing caused by excessive belt slippage. Because most modern engines are equipped with only one or two belts, an unnoticed defect can rapidly develop into a catastrophic failure.

TYPES OF BELTS
Belts fall into three different categories: v-belts, serpentine belts and specialized belts like camshaft and balance shaft timing belts. V-belts have been with us the longest, having been introduced in the 1920s to power water pumps and generators on cars like the Ford Model T. As engine accessory drives became more complex, automakers began installing serpentine belts to simplify drive belt architecture. Unlike a v-belt, a serpentine belt uses both the smooth and the grooved sides to drive accessories. Specialized belts like timing belts are used to maintain precise timing intervals on cog-driven timing devices like engine camshafts and balance shafts. These belts must be precision-built and must last at least 100,000 miles before needing replacement.

While v-belts generally don’t require special tools for installation, serpentine belts often require special wrench sets available from aftermarket sources to relieve the tension on the automatic belt tensioner so the belt can be replaced. When working in confined areas between the engine and fender, technicians may also need a set of zero-offset wrenches to loosen accessory mounting bolts on front-wheel drive vehicles. A tool designed to help thread the belt over the pulleys also comes in handy on front-wheel drive applications.  

Timing belts usually require special tools to hold camshafts in alignment while the belt is being replaced.  Some timing belts also require special tensioning tools to adjust belt tension. Because some engines use the water pump to tension belts, special tools are needed to adjust the position of the water pump on the engine.

RELATED SALES FOR BELT REPLACEMENTS
Because accessory drive components tend to wear out at the same rate, many shops recommend replacing the water pump, belt tensioner, idler pulleys, and camshaft and crankshaft seals when the timing belt is replaced.  Similarly, when a water pump or power steering pump is replaced, the belts, idler pulleys and tensioner pulley should be inspected and replaced if needed. In addition, if the radiator is removed, the radiator and other coolant hoses should be replaced if required.

UNDERSTANDING BELT PART NUMBERS
Because today’s engine compartments are so compact, serpentine belts have become very application-specific. In short, serpentine belts must be of a specific length, width and have the correct number of v-ribs to fit the application. Although v-belts generally have wider latitudes of interchangeability, they, too, must be of a specific length, width and angle to provide correct tension adjustment and pulley fit.
A belt part number usually identifies the type of belt and the length and width of that belt. Keep in mind that automotive belts may differ in design from belts used for implement applications. A lawnmower drive belt, for example, may not interchange with an automotive drive belt. To minimize returns, use the eight digits in the vehicle identification number (VIN) to correctly identify the engine and its accessories. If the vehicle has been modified or the application is in doubt, match the new belt with the old either by direct measurement or by cross-referencing the old belt’s part number with the new.

STOCKING TRENDS
Vehicle populations dwindle as time passes and so do the sales for those belts. Consequently, it’s extremely important to ensure that your belt inventory remains active by reviewing sales histories of individual part numbers to cull out slow-moving and shelf-worn merchandise. Keeping in mind that Asian, Euro and domestic vehicle populations vary proportionately from area to area, always tailor your belt and hose inventory to match your vehicle demographics. Last, fleet and similar types of commercial vehicles require more frequent belt replacements, so keep enough of those numbers in stock to support demand.

WHY HOSES WEAR OUT
Hoses are designed to provide a flexible connection between two fixed components like an engine and radiator.  Unlike a belt, a rubber hose is usually attacked from the inside by harsh chemicals forming within the cooling system. Hoses are also attacked externally by high underhood temperatures and atmospheric pollution.
Ultimately, a deteriorated coolant hose begins to swell or develop leaks at the hose connections. A radiator hose should not only be tested for loss of flexibility, it should also be tested for internal deterioration by allowing the engine to cool and slowly releasing the pressure on the radiator cap. With the pressure released, squeeze the sides of the hose together. If the hose feels hard and brittle or spongy and mushy, it should be replaced.

TYPES OF HOSES
Hose is generally designed to transport specific fluids at a specific temperatures and pressures. To illustrate, while a low-pressure fuel hose designed for a carbureted engine and a high-pressure fuel hose designed to transport fuel for a fuel-injected engine might appear the same, the low-pressure hose will cause a catastrophic failure when used in a fuel injection application. Similarly, a high-pressure oil hose is generally made with steel or fabric reinforcements to help contain hot oil under high operating pressures. In contrast, fuel line hose is made to contain highly volatile petroleum fluids at relatively low temperatures and pressures. And, while radiator hose might look like a good substitute for gasoline tank filler neck hose, it will rapidly deteriorate when exposed to gasoline.

MOLDED HOSES
Because modern engine compartments are very confined, most applications require molded radiator and heater hoses to help navigate tight bends and make connections with different inlet and outlet diameters. To avoid kinking, the small coolant hoses connected to the throttle body and intake manifold are molded as well. Substituting a molded hose with a universal-fit or bulk hose can stress and ultimately break radiator and heater core connections and is therefore not recommended.

BULK HOSE
Bulk hose continues to be a large seller because many older vehicles still use bulk coolant, fuel and vacuum hose. Because, coolant, fuel, oil and vacuum hoses aren’t interchangeable, it’s very important to sell hose that matches the application. When stocking bulk hose, it’s important to label the application for each roll of hose and to have a spare roll handy for the commercial customer or for the buyer who needs a longer length of hose. To avoid waste in bulk hose, try selling a bit more hose than is needed by convincing the customer that it’s much cheaper to cut off excess hose than it is to discard a length of hose because it’s been cut too short.

SALES OPPORTUNITIES FOR BELTS AND HOSES
A belt sales opportunity exists when a belt-driven accessory like a water pump, power steering pump, alternator, air conditioning compressor or air injection pump is being replaced. Similarly, a hose sales opportunity presents itself when a water pump, radiator or heater core is being replaced. When selling a power steering pump, don’t forget to ask about the condition of the power steering hoses. If a new or remanufactured engine is being sold, don’t forget to mention that the warranty might be voided if the engine is damaged by a leaking hose or broken accessory drive belt.  Belt and hose sales represent one of the most lucrative add-on sales opportunities. Don’t miss your chance to “make the sale!”

Gary Goms is a former educator and shop owner who remains active in the aftermarket service industry. Gary is an ASE-certified Master Automobile Technician (CMAT) and has earned the L1 advanced engine performance certification. He is also a graduate of Colorado State University and belongs to the Automotive Service Association (ASA) and the Society of Automotive Engineers (SAE). 

You May Also Like

Auto Care Association Leaders Visit Northwood University

Auto Care President and CEO Bill Hanvey was the guest lecturer for several Northwood automotive aftermarket courses at its Midland campus.

Bill Hanvey Auto Care Northwood

Photo caption: Bill Hanvey, president and CEO, Auto Care Association (pictured on the right), teaches an automotive aftermarket course during a recent visit to Northwood University in Midland, Michigan.

Leaders from the Auto Care Association recently visited Northwood University to meet with students enrolled in automotive aftermarket courses.

MEMA Aftermarket Suppliers Achieves UAF Gold Lifetime Trustee Status

The designation goes to “outstanding donors who significantly support the UAF’s mission.”

MEMA UAF Gold Lifetime Trustee
ASE Ed. Foundation, Auto Dealer Associations Tackle Tech Shortage

Three student competitions are currently scheduled for 2024, with more being planned.

ASE Education Foundation Auto Dealers
Northwood U Announces 2024 Class of 20 Under 40 Honorees

The program recognizes NU alumni who are ambitious professionals doing great things in their careers, organizations or communities.

Northwood University 20 Under 40
Two NexaMotion Units Expand Product Offerings, Open New Locations

Transtar Industries and C&M Auto Parts are expanding.

NexaMotion Expanding

Other Posts

GPC Reports 2023 Results, Announces Global Restructuring Program

The restructuring includes a voluntary retirement offer in the United States.

Kalitta Motorsports, Dayco Announce Partnership, Distributor Agreement

Dayco will have branding on J.R. Todd’s DHL GR Supra funny car, and Kalitta is the exclusive at-track distributor of Dayco 11-mm racing blower belts for nitro engines.

Dayco Kalitta
AutoPartSource/Momentum USA Receives O’Reilly’s Sales & Service Award

This is the second year in a row that O’Reilly has honored AutoPartSource/Momentum USA with the award.

Momentum USA OReilly