Opinion: Cheap Brake Jobs Are Not Cheap

Opinion: Cheap Brake Jobs Are Not Cheap

Brakes should not a loss leader for shops, says Brake & Front End Editor Andrew Markel.

By Andrew Markel

In the 1930s, during the Great Depression, you could get all four brakes relined for $19.99 (springs and hardware extra). If you calculate what that means in 2012 dollars, it would cost $282 according to the Consumer Price Index. So why are shops performing $99 brake jobs?

Brakes should not a loss leader for shops. Also, brake pad sales should not be a low margin item in order to compete. It is not a service like an oil change or filter replacement that is used to bring vehicles in for service so you can spot other worn or broken parts that need to be repaired. It is a safety service and the consumer should be charged accordingly.

So what does it take to get undercar shops to get out of the $99 pad swap doldrums? Just like in the 1930s, the shops that will survive are able to put a value on brake service for the consumer and are able to charge more than $99. There is no way to measure a rotor for thickness and runout efficiently and profitably on a $99 brake job. Between setup and making the measurements, it takes at least 10 minutes. But, this must be performed even if you are just slapping in new pads. Shops that do not do this often have higher than normal warranty returns.

Selling Pads

The brake repair market is starting to become dominated by a “good enough” mentality when it comes to $99 brake jobs. Good enough to some is just being able to stop in a “reasonable” distance at normal driving and last for 20,000 miles. But, when asked to perform an emergency stop or a series of hard stops, the vehicle can become unsafe with longer stops and a low pedal.

Are you sure that little old lady doesn’t drive with two feet? Can you be sure that that a truck will never tow a boat? Is it really worth installing cheap brake pads in order to be able to advertise and hopefully make profit on a $99 brake special?

What standards should you extol when selling replacement brake pads? Try them for yourself! Set aside some time when the shop is not busy or on a weekend to try out the brands of brake pads you sell. Perform at least four emergency stops from 55 mph to a dead stop back-to-back. Let your right foot be the judge. A series of hard stops will simulate the punishment a pad might have on a major metropolitan freeway during extreme stop-and-go traffic.

Inferior brake pads will start to fade and pedal travel will be almost to the floor. Also, inferior pads will start to smell worse than the average burnt clutch. Some inferior brake pads may have a very acrid or pungent aroma due to the use of cheap glues and fillers. Also, the smell can be attributed to coatings and paints that may be burning. Some inferior brake pad manufacturers use only a handful of friction material formulations across an entire product catalog. This means that the same friction material may be used on a SUV and compact, the only thing they change is the backing plate.

Selling Hardware
New hardware is critical to protecting the driver’s investment in a proper brake job.

Brake hardware for disc brakes is not a dealer-only item. A local jobber might carry three lines of hardware. This product category is more than shims, anti-rattle clips or dust shields. Many of these lines of products include items like caliper brackets, slides and all the soft parts to restore the system to like-new condition. Many of these parts are at reasonable prices that you and your customer cannot refuse.

Heating and cooling cycles can weaken springs and anti-rattle clips. Weak hardware parts can result in excessive caliper/pad movement or binding, causing noise and other related problems. This can lead to uneven and premature pad wear, rotor warpage and pulling.

Some springs and clips can be difficult to install. Some anti-rattle clips may resemble Chinese finger traps when you are trying to reinstall them back on the car. But leaving them out is not an option.

When rust and corrosion build up on a floating caliper’s slides or bushings, it can prevent the caliper from centering itself over the rotor when the brakes are applied. Not only does this reduce effective braking force and increase the vehicle’s stopping distance, it also causes uneven pad wear. When technicians think of brake hardware, they think springs, clips and slides. But soft parts like dust shields, grommets and bushings need just as much attention.

Most floating brake calipers use a rubber or plastic insulator or shim around the mounting bolts of the caliper. This sleeve of soft material loses resiliency over its lifetime.

To perform a $99 brake job, a technician cannot clean and lubricate the caliper guide pins. A technician only has enough time to pull one pin, rotate the caliper, push the piston back, replace the pads and then follow the reverse steps.

Brake lubricants are critical in returning the brake system to optimal operating condition. There are three criteria to remember when selecting a brake lubricant. First, does it say that it’s a brake lubricant on the package? If not, don’t use it. Some lubricants may say they are a silicone- or molybdenum disulfide-based, but they may not be formulated to work on brakes. Second, look at the effective temperature range of the lubricant. At minimum, a lubricant should be able to handle 400 degrees F. Third, check to see if it contains petroleum distillates or any substance that can be detrimental to soft parts.

It takes at least seven minutes to perform a proper brake job test drive. Even line techs at dealerships get paid to perform this procedure. Just backing the car out of the bay can cause a comeback and leave service dollars on the table. A test drive can ensure the brake system is operating properly. It can also help you to spot other problems with the vehicle. The other reason a test drive must be performed is to mate the pads to the rotors. This can be called “break in” or “burnishing” the pads. Burnishing also can help to transfer a layer of the friction material onto the rotor. Some manufacturers call this transfer-layer technology and it can help to increase the life of the rotor.

You May Also Like

Assault on Batteries

Even EV batteries aren’t immune to the effects of extreme winter weather.

EV Batteries

This winter, extreme weather patterns have been disrupting daily routines nationwide. Flooding, snowfall and subzero temperatures all have taken a toll on our roadways and vehicles, leaving many stranded or unable to leave their homes. For those who can make it out to the streets, driving conditions can be hazardous. Having a reliable, fully charged battery is critical during these weather events.

The Evolution of Automotive Fuel Systems

The frequency of changes has increased in recent decades.

Fuel Systems
When Springs Break

Unfortunately, the kind of spring break that leaves ‘road earrings’ isn’t a desirable getaway.

Broken Springs
Understanding the Customer Lifecycle

Knowing the most effective ways to connect with each customer type helps create repeat business and build your brand.

Customer Lifecycle
Check the Part: Return Guide for Fluid Reservoirs

Dorman recommends these four steps to determine if it’s a valid warranty claim.

Fluid Reservoir

Other Posts

Bleeding the Brakes (Part 2)

With the proper preparation and a little bit of patience, brake bleeding can be a routine job for your customers, whether they’re professionals or DIYers.

Bleeding the Brakes Part 2
Bleeding the Brakes (Part 1)

It’s a simple concept, but it’s not without the occasional headache.

Bleeding the Brakes Part 1
Recommending the Right Brake Pads

These small but mighty parts play a crucial role in stopping your vehicle.

Recommending the Right Brake Pads
Recommending High-Performance Brake Rotors

The design of the rotor determines how it can handle the heat.

Performance Brake Rotors