ASE P2 TEST PRIMER: Suspension and Steering

ASE P2 TEST PRIMER: Suspension and Steering

Major components in the suspension include springs (coil, leaf, torsion bar and air springs), shock absorbers and/or struts (twin tube or monotube, low or high pressure gas charged, and some may be electronically adjustable), control arms and bushings, ball joints (which may be an integral part of some unitized control arm assemblies), and sway bar and bushings.


Major components in the steering include the steering gear (rack and pinion or recirculating ball, manual or power assisted), power steering pump and hoses (not used with electronic steering), tie rods and tie rod ends, idler arm and center link (used only with recirculating ball steering gear systems), steering stabilizer (if used) and steering column (including flexible couplings that connect the steering gear to the column shaft).

Major components in the suspension include springs (coil, leaf, torsion bar and air springs), shock absorbers and/or struts (twin tube or monotube, low or high pressure gas charged, and some may be electronically adjustable), control arms and bushings, ball joints (which may be an integral part of some unitized control arm assemblies), and sway bar and bushings.

All steering and suspension parts wear over time. Wear increases play and can lead to undesirable changes in wheel alignment, resulting in steering, handling and ride-quality problems, uneven or rapid tire wear, noise or even parts failures. Worn parts cannot be realigned and must be replaced. Parts such as tie rod ends and struts also require realigning the wheels following installation.

Many newer vehicles have electronic steering that use an electric motor to provide power assist. But most older cars have hydraulically assisted power rack and pinion steering. Common problems include fluid leaks at the rack bellows, line fittings and hoses. Internal seal wear can cause a loss of power assist. Worn racks are usually replaced as an assembly (with tie rods) to save labor.

Steering noise may be caused by a worn power steering pump or slipping belt. Power steering pumps require power steering fluid that meets the vehicle’s specifications. Leaky power steering hoses can be replaced with preassembled hoses or custom made-to-order hoses. The power steering system should always be flushed to remove contaminants when replacing a steering rack, pump or hoses.

The suspensions on most vehicles do not require lubricating with chassis grease, but some ball joints, tie rod ends and U-joints on older vehicles or heavy-duty use vehicles may be greasable.

Ball joints, tie rod ends and idler arms that are loose (play exceeds specifications) must be replaced.
Shocks and struts are the most commonly replaced suspension parts due to wear, fluid leakage or damage. Preassembled struts are ready to install and do not require a spring compressor. Electronic shocks and air ride suspensions on older vehicles can often be converted to less expensive conventional shocks/struts when repairs are needed.

Required to pass this section of the P2 test:
1. Identify major steering and suspension components.
2. Identify component function and common reasons for replacement.
3. Identify related items, including lubricants and service tools.
4. Provide basic use, maintenance, installation and warranty information.

You May Also Like

Assault on Batteries

Even EV batteries aren’t immune to the effects of extreme winter weather.

EV Batteries

This winter, extreme weather patterns have been disrupting daily routines nationwide. Flooding, snowfall and subzero temperatures all have taken a toll on our roadways and vehicles, leaving many stranded or unable to leave their homes. For those who can make it out to the streets, driving conditions can be hazardous. Having a reliable, fully charged battery is critical during these weather events.

The Evolution of Automotive Fuel Systems

The frequency of changes has increased in recent decades.

Fuel Systems
When Springs Break

Unfortunately, the kind of spring break that leaves ‘road earrings’ isn’t a desirable getaway.

Broken Springs
Understanding the Customer Lifecycle

Knowing the most effective ways to connect with each customer type helps create repeat business and build your brand.

Customer Lifecycle
Check the Part: Return Guide for Fluid Reservoirs

Dorman recommends these four steps to determine if it’s a valid warranty claim.

Fluid Reservoir

Other Posts

MAF and MAP Sensors

These small-but-mighty components play an outsized role in keeping fuel-injected engines running smoothly.

MAF and MAP Sensors
Mastering the Multimeter

It’s a tool that will expand your diagnostic ability.

Multimeter
Electronic Parking Brakes

Safety, convenience and holding power – what’s not to love?

Electronic Parking Brake
Navigating the Lubricant Labyrinth

A surge in specialized engine oils has led to some confusion over the correct recommendations for each application.

Motor Oil