Opinion: Cheap Brake Jobs Are Not Cheap

Opinion: Cheap Brake Jobs Are Not Cheap

Brakes should not a loss leader for shops, says Brake & Front End Editor Andrew Markel.

By Andrew Markel

In the 1930s, during the Great Depression, you could get all four brakes relined for $19.99 (springs and hardware extra). If you calculate what that means in 2012 dollars, it would cost $282 according to the Consumer Price Index. So why are shops performing $99 brake jobs?

Brakes should not a loss leader for shops. Also, brake pad sales should not be a low margin item in order to compete. It is not a service like an oil change or filter replacement that is used to bring vehicles in for service so you can spot other worn or broken parts that need to be repaired. It is a safety service and the consumer should be charged accordingly.

So what does it take to get undercar shops to get out of the $99 pad swap doldrums? Just like in the 1930s, the shops that will survive are able to put a value on brake service for the consumer and are able to charge more than $99. There is no way to measure a rotor for thickness and runout efficiently and profitably on a $99 brake job. Between setup and making the measurements, it takes at least 10 minutes. But, this must be performed even if you are just slapping in new pads. Shops that do not do this often have higher than normal warranty returns.

Selling Pads

The brake repair market is starting to become dominated by a “good enough” mentality when it comes to $99 brake jobs. Good enough to some is just being able to stop in a “reasonable” distance at normal driving and last for 20,000 miles. But, when asked to perform an emergency stop or a series of hard stops, the vehicle can become unsafe with longer stops and a low pedal.

Are you sure that little old lady doesn’t drive with two feet? Can you be sure that that a truck will never tow a boat? Is it really worth installing cheap brake pads in order to be able to advertise and hopefully make profit on a $99 brake special?

What standards should you extol when selling replacement brake pads? Try them for yourself! Set aside some time when the shop is not busy or on a weekend to try out the brands of brake pads you sell. Perform at least four emergency stops from 55 mph to a dead stop back-to-back. Let your right foot be the judge. A series of hard stops will simulate the punishment a pad might have on a major metropolitan freeway during extreme stop-and-go traffic.

Inferior brake pads will start to fade and pedal travel will be almost to the floor. Also, inferior pads will start to smell worse than the average burnt clutch. Some inferior brake pads may have a very acrid or pungent aroma due to the use of cheap glues and fillers. Also, the smell can be attributed to coatings and paints that may be burning. Some inferior brake pad manufacturers use only a handful of friction material formulations across an entire product catalog. This means that the same friction material may be used on a SUV and compact, the only thing they change is the backing plate.

Selling Hardware
New hardware is critical to protecting the driver’s investment in a proper brake job.

Brake hardware for disc brakes is not a dealer-only item. A local jobber might carry three lines of hardware. This product category is more than shims, anti-rattle clips or dust shields. Many of these lines of products include items like caliper brackets, slides and all the soft parts to restore the system to like-new condition. Many of these parts are at reasonable prices that you and your customer cannot refuse.

Heating and cooling cycles can weaken springs and anti-rattle clips. Weak hardware parts can result in excessive caliper/pad movement or binding, causing noise and other related problems. This can lead to uneven and premature pad wear, rotor warpage and pulling.

Some springs and clips can be difficult to install. Some anti-rattle clips may resemble Chinese finger traps when you are trying to reinstall them back on the car. But leaving them out is not an option.

When rust and corrosion build up on a floating caliper’s slides or bushings, it can prevent the caliper from centering itself over the rotor when the brakes are applied. Not only does this reduce effective braking force and increase the vehicle’s stopping distance, it also causes uneven pad wear. When technicians think of brake hardware, they think springs, clips and slides. But soft parts like dust shields, grommets and bushings need just as much attention.

Most floating brake calipers use a rubber or plastic insulator or shim around the mounting bolts of the caliper. This sleeve of soft material loses resiliency over its lifetime.

To perform a $99 brake job, a technician cannot clean and lubricate the caliper guide pins. A technician only has enough time to pull one pin, rotate the caliper, push the piston back, replace the pads and then follow the reverse steps.

Brake lubricants are critical in returning the brake system to optimal operating condition. There are three criteria to remember when selecting a brake lubricant. First, does it say that it’s a brake lubricant on the package? If not, don’t use it. Some lubricants may say they are a silicone- or molybdenum disulfide-based, but they may not be formulated to work on brakes. Second, look at the effective temperature range of the lubricant. At minimum, a lubricant should be able to handle 400 degrees F. Third, check to see if it contains petroleum distillates or any substance that can be detrimental to soft parts.

It takes at least seven minutes to perform a proper brake job test drive. Even line techs at dealerships get paid to perform this procedure. Just backing the car out of the bay can cause a comeback and leave service dollars on the table. A test drive can ensure the brake system is operating properly. It can also help you to spot other problems with the vehicle. The other reason a test drive must be performed is to mate the pads to the rotors. This can be called “break in” or “burnishing” the pads. Burnishing also can help to transfer a layer of the friction material onto the rotor. Some manufacturers call this transfer-layer technology and it can help to increase the life of the rotor.

You May Also Like

A Closer Look at Lincoln-Mercury

The Mercury brand was shuttered in 2010, while Lincoln is enjoying a bit of a renaissance.

Platform-sharing” and “badge engineering” are terms often used to describe the common industry practice of developing multiple vehicle models from a common design. The economy of a single design underpinning multiple vehicles allows manufacturers to streamline the development process, and to provide the buyer with options across their base, mid-line and luxury divisions. Much of this “twinning” occurs within a manufacturer’s “family” of brands, but cooperating with rival manufacturers already well-established in a market allows the manufacturer to produce vehicles outside their wheelhouse.

HDA Truck Pride’s Tina Hubbard on Baseball, Right to Repair

Hubbard, president and CEO of HDA Truck Pride, asserts: “The only way to win is for every one of us to get involved.”

Sue Godschalk: ‘One Year Equals 365 Opportunities’

Godschalk, president of Federated Auto Parts, is optimistic about the back half of 2023.

Sanjay Patel on Supporting Carquest’s ‘Diverse Business’

“As a support team, collaboration is of the utmost importance,” says Patel, president of Carquest North America.

APA’s Steve Tucker: Independent Aftermarket Alive and Well

“The strengths of the players in the independent space are often difficult for the big-box guys to replicate.”

Other Posts

Continental Expands Line of Electronic Parking Brake Calipers

The 10 newly released parts provide coverage for more than 5 million vehicles in operation.

O’Reilly Unveils BrakeBest Select Pro Pads and Rotors

The private-label pads and rotors are available online and in O’Reilly stores nationwide, including Puerto Rico.

Momentum USA Unveils Max Duty Brake Pads

The brake pads provide three levels of protection for fleet, emergency-service and other severe-duty requirements.

JC Washbish: ‘Selling Better’ Has Been the Goal All Along

Washbish, VP of sales and marketing for the Alliance, is enthusiastic about the new partnership with Federated.